Symbol > Male Symbol 
This tool allows you to add a symbol to the male.
Edit bar controls
Symbol Browse 
This will open the Symbol Select form allowing you to choose the required male symbol.
Rotate 
This option allows you to rotate the symbol by changing the angle.
Machine Settings 
From the pulldown list select the Stripper Machine setting required. Defined in the Machine settings is if the new geometry is to be created in blocks and if the geometry is to be created in the current layer or a specified layer for each unit.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper Machine Settings form.
System Settings 
From the pulldown list select the Stripper system settings required.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper System Settings form.
How to use the tool
The origin point of the symbol will be the insertion point of the symbol. The symbol selected will appear on your cursor and then be positioned.
Symbol > Female Symbol 
This tool allows you to add a symbol to the female.
Edit bar controls
Symbol Browse 
This will open the Symbol Select form allowing you to choose the required female symbol.
Rotate 
This option allows you to rotate the symbol by changing the angle.
Machine Settings 
From the pulldown list select the Stripper Machine setting required. Defined in the Machine settings is if the new geometry is to be created in blocks and if the geometry is to be created in the current layer or a specified layer for each unit.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper Machine Settings form.
System Settings 
From the pulldown list select the Stripper system settings required.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper System Settings form.
How to use the tool
The origin point of the symbol will be the insertion point of the symbol. The symbol selected will appear on your cursor and then be positioned.
Symbol > Double Symbol 
This tool allows you to add a symbol to the female and a symbol to the male with the same insertion point.
Edit bar controls
Symbol Mode 
From the pulldown list choose the double symbol required.
Rotate 
This option allows you to rotate the symbol by changing the angle.
Machine Settings 
From the pulldown list select the Stripper machine setting required. Defined in the Machine settings is if the new geometry is to be created in blocks and if the geometry is to be created in the current layer or a specified layer for each unit.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper Machine Settings form.
System Settings 
From the pulldown list select the Stripper system settings required.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper System Settings form.
How to use the tool
The origin point of each symbol will be the insertion point of the symbol. The symbols will appear on your cursor and then be positioned.
Symbol > Symbol Pattern 
This tool allows you to add the symbol patterns for the male, female and front edge units as defined in the Stripper machine settings.
Edit bar controls
Male 
If this option is checked, then the patterns assigned to the male unit will be inserted once Accept has been clicked.
Female 
If this option is checked, then the patterns assigned to the female unit will be inserted once Accept has been clicked.
Front Edge Upper 
If this option is checked, then the patterns assigned to the front edge upper unit will be inserted once Accept has been clicked.
Front Edge Lower 
If this option is checked, then the patterns assigned to the fromt edge lower unit will be inserted once Accept has been clicked.
Accept 
Press this button to accept the selected Male, Female and Front Edge options and the tool will then load each pattern in turn.
Machine Settings 
From the pulldown list select the Stripper machine setting required. Defined in the Machine settings is if the new geometry is to be created in blocks and if the geometry is to be created in the current layer or a specified layer for each unit.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper Machine Settings form.
System Settings 
From the pulldown list select the Stripper system settings required.
You can make a temporary override to the settings shown by pressing the edit button 
and changing the values shown in the Stripper System Settings form.
How to use the tool
The patterns assigned to the male, female and front edge units can be inserted by checking the options required and pressing Accept. The tool will then load each pattern in turn, running the Symbol pattern tool for each.
Symbol patterns can be automatically placed or they may require you to place them. Any patterns that require you to place them manually will display a prompt on the status bar. If the pattern is to be placed once, when the pattern has been positioned the next pattern will be loaded. If the pattern is to be placed multiple times, when you have placed all instances of the current pattern, then press Continue 
to continue with the next pattern. When all the symbol patterns have been placed, the Delete symbols tool is run to allow you to delete any symbols you wish.
To delete symbols placed, select the symbol to be deleted in the Symbols 
pull down and from the Mode 
select Delete Symbols or Select Symbols. If the mode is Delete Symbols, pick or box the symbols to be deleted and they will be deleted as they are picked; if the mode is Select Symbols then pick or box the symbols to keep and press Delete Others 
to delete the symbols not selected. Rewind 
will add the last deleted symbols back. Cancel 
will cancel the symbol pattern mode.
When complete, press Finish 
on the edit bar.